甘肃11选5APP走势图


Horizontal Flammability Test

 

Vertical Flammability Test The Oxygen Index Test
Glow Wire Test Horizontal Flammability Test
Needle-flame Test Flammability of Interior Materials

 

Test standard:

UL94-2015, 4943.1-2011 GB, 2408-2008 GB/T, 5169.16-2008 GB/T, etc..

 

Scope:

Plastic, foam, film, textile, paint, rubber, etc., are not applicable to building materials.

 

Sample size:

Length 125±5mm, width 13±0。5mm, thickness 0。025~13mm

 

Test pretreatment:

A set of 3 samples at23±2℃, 50±5%RH adjustment at least 48H

 

Tested Condition:

The flame height is 20±1mm, the ignition time is 30±1s, the flame source is tilted 45 degrees, and the sample holder is kept at 45 degrees with the horizontal plane。

 

HB Criteria:

1)Not have a burning rate exceeding 40mm per minute over a 75mm span for specimens having a thickness of 3.0~13mm, or

2)Not have a burning rate exceeding 75mm per minute over a 75mm span for specimens having a thickness less than 3.0mm, or

3)Cease to burn before the 100mm reference mark.

4)A material classified HB in the 3.0+0.2 mm thickness shall automatically be classed HB down to a 1.5 mm minimum thickness without additional testing.

 

Test schematic diagram

 

Case:

Typical cases

Reference standard:

Fuel test for plastic materials for UL94-2015 equipment and appliances.

Tested Flow:take picture→mark on specimens at 25mm and 100mm→set parameters of instrument→start testing 

 

Tested Condition:

Level of combustion flame height requirement is 20 ± 1mm, the ignition time is 

30±1s, Flame source tilt 45 °, with the level of the sample holder maintained between 45 °。

Sample Size:127mm×13mm×4.4mm

 

HB Criteria:

1)Not have a burning rate exceeding 40mm per minute over a 75mm span for specimens having a thickness of 3。0~13mm, or

2)Not have a burning rate exceeding 75mm per minute over a 75mm span for specimens having a thickness less than 3.0mm, or

3)Cease to burn before the 100mm reference mark。

4)A material classified HB in the 3.0+0.2 mm thickness shall automatically be classed HB down to a 1.5 mm minimum thickness without additional testing.

 

Test result:

 

Test sample test result(mm/min)
--------- 1 30.1
2 32.5
3 28.7
Maximum value 32.5

 

Conclusion:The samples comply with UL94-2015 HB.



  • Contact Us
  • MTT Shenzhen

    Tel: 400-850-4050

    Fax: 0755-2782 1672

    Email: marketing@mttlab。com

     

    MTT Suzhou

    Tel: 400-118-1002

    Fax: 0512-6275 9537

    Email: marketing@czptgs.com

     

    MTT Shanghai

    Tel: 400-118-1002

    Email: marketing@mttlab。com

     

    MTT Dongguan

    Tel: 400-116-1002

    Email:marketing@mttlab。com

Shenzhen Meixin Testing Technology Co。, Ltd。

微信
甘肃11选5官网 甘肃11选5 甘肃11选5官网 甘肃11选5官网 甘肃11选5走势图 甘肃11选5 甘肃11选5APP走势图甘肃11选5APP下载 甘肃11选5 甘肃11选5APP走势图甘肃11选5APP下载 甘肃11选5